All the answers to your questions: practical guides to the installation, use and correct maintenance of your Elleci product.
When the Plano Plus, Quadro and Leaf ovens are locked, the error code ‘ER’ with a number next to it (e.g. ‘ER0’) appears on the display. In such a case you should refer to the list below with reference to the model oven you own: For the Plano plus, Quadro and Leaf ovens, the error codes shown on the display are as follows: ER10 -> This is displayed when the voltage drops below 170 V (±10). If the voltage increases above 180 V the error code disappears. Please check the mains voltage, which should be higher than 180 V. ER11 -> This is displayed when the motherboard temperature is above 105°C. Check that the fan cooling system is working. If the error persists, please contact support directly by clicking the following link: https://www.elleci.com/it/come-possiamo-aiutarti/richiedi-assistenza/apri-una-pratica-di-richiesta-assistenza/. ER8 -> This is displayed to prevent the oven from drawing more voltage than necessary. If the error persists, the motherboard will need to be replaced and you will need to contact support by clicking directly on the following link: https://www.elleci.com/it/come-possiamo-aiutarti/richiedi-assistenza/apri-una-pratica-di-richiesta-assistenza/. ER6 -> This is displayed when the error occurs after six hours of inactivity. It will be cleared when the unit is next used. door -> This is displayed to inform you that the oven door is open during the Steam Clean function. It will disappear once the door is closed properly. ER3 -> This is displayed when the ‘door lock’ function does not function either electrically or mechanically. You will need to check the door closure and if the error persists you will need to contact support by clicking directly on the following link: https://www.elleci.com/it/come-possiamo-aiutarti/richiedi-assistenza/apri-una-pratica-di-richiesta-assistenza/. ER5 -> This is displayed when the error occurs after six hours of inactivity. It will be cleared when the unit is next used.
Replacing the oven gasket is a very simple operation that can be carried out by do-it-yourself enthusiasts, but it is always advisable to contact qualified technical personnel. The steps for replacement are as follows:
1. Switch off the power supply by removing the plug and turning off the oven switch to ensure you are operating in a completely safe environment.
2. Then open the oven and start pulling the gasket to be replaced off the frame.
3. Carefully apply the new gasket using the reverse procedure.
You can check the availability of spare parts directly from the online shop: https://elleci.shop/
If switching on the oven triggers the circuit breaker, check whether: 1. the appliance is correctly connected to the power socket; 2. the domestic electrical installation is compliant; Once external causes have been ruled out, if the problem persists, you should open a support file by clicking directly on the following link: https://www.elleci.com/it/come-possiamo-aiutarti/richiedi-assistenza/apri-una-pratica-di-richiesta-assistenza/.
If the oven inadvertently switches itself off, you will need to check that the installation and electrical connections have been completed correctly. Once all checks have been carried out, in the case of an oven with a display, check whether it is showing specific ‘ER’ codes. If so, consult the accompanying user manual. If the problem persists, you should open a support file by clicking directly on the following link: https://www.elleci.com/it/come-possiamo-aiutarti/richiedi-assistenza/apri-una-pratica-di-richiesta-assistenza/.
To remove the ‘DEMO’ and ‘SHOP’ error messages on the appliance’s display, you must follow the procedure for the specific oven model you have. Here are the procedures for unlocking and resolving before a possible notification: – For the Plano Plus oven when the product is in operation (not in standby mode), ‘M’ and ‘+’, ‘-’ must be tapped together. – For the Quadro oven when the product is in operation (not in standby mode), ‘P’ and ‘Thermostat’ must be tapped together. If you are unable to resolve the issue using the above procedure, you should contact support directly by clicking the following link: https://www.elleci.com/it/come-possiamo-aiutarti/richiedi-assistenza/apri-una-pratica-di-richiesta-assistenza/.
Italy
